Icom F50V 11 RC POLICE FIRE HAM 128CH 5W 136-174 MHZ

SquareTrade © AP6.0... SquareTrade © AP6.0... ITEM... 1 NEW Icom IC-F50V 11 RC 5 watt 128 channel two way radio (frequency range 136-174 mhz) this model is programmable for both wide and narrow band... Supplied AccessoriesAntenna (Length may differ according to version)Alligator-type belt clip, MB...

SquareTrade © AP6.0


SquareTrade © AP6.0

ITEM

1 NEW Icom IC-F50V 11 RC 5 watt 128 channel two way radio (frequency range 136-174 mhz) this model is programmable for both wide and narrow band.

Supplied Accessories

• Antenna (Length may differ according to version)
• Alligator-type belt clip, MB-98
• Battery pack, BP-227
• Rapid Battery Charger BC-119N

Never miss important calls
with loud audio, vibration alert and voice recorder!

Vibration alert function

When a pre-programmed 2-tone/5-tone code or call from a specific user (MDC mode only) is received, the radio vibrates powerfully enough to be felt through heavy clothing.

8 minute voice recorder

When a pre-programmed 2-tone/5-tone code or a SelCall (MDC mode only) is received, the voice recorder automatically starts recording the incoming message. You will not miss an important call even when you are temporarily away from the radio. You can manually start recording incoming calls and also your own message. It records up to a maximum of 8 minutes (Or up to 48 calls of 10 sec. recording time).

700mW audio output

The IC-F50V delivers a loud 700mW* audio output with the built-in BTL amp. The built-in audio compander provides clear, low noise communications. Improved bass characteristics also betters the audio quality.
* Typical with internal speaker.

Lone worker function for remote check in

When the radio is not operated for a preset period (1 to 255 min.), the radio sounds a beep and requires you to push the emergency button. If the emergency button is not pushed for a preset time (1 to 255 sec.), an emergency signal automatically transmits and informs your co-worker or dispatcher that something may have happened to the individual worker.

IP67, dust-tight and waterproof protection

The IC-F50V has outstanding protection against dust and water that is equivalent to IP67. The IC-F50V can withstand submersion in 1m depth of water for up to 30 minutes and has dust-tight construction that prevents the ingress of dust.

Most popular signalings built-in

Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone and MDC signaling capabilities to set up your talk group or selective calling. The IC-F50V can decode ten 2-Tone codes or eight 5- Tone codes on a channel. When a matched tone is received, the following actions are programmable for each code.

• Bell icon
• Answer back call
• Beep sound
• Auto transmit
• Radio Stun/Kill/Revive
• Voice recorder
• Vibration alert

MDC 1200 Compatible

The following selective calling and ANI features are available with the built-in MDC signaling.

• PTT ID
• Radio check
• Caller ID
• Call alert
• SelCall
• Emergency, emergency mic monitoring
• 500 Aliases
• Status/message
• Radio stun/revive

Mode dependent scan

In the mode dependent setting, the scanning setting is dependent on the operating channel. When you change the operating channel, the scanning list automatically changes to the operating channel setting. It is convenient when you move to a different operating area and change an operating channel, you don’t have to change the scanning setting.

Enhanced scanning

The Tx channel while scanning can be programmed per scanning list. The talk back function allows you to transmit on the channel detected after scanning resumes after a preset time, prior to the Tx channel setting. The nuisance delete function temporarily deletes a busy channel from the scanning list. Backlight at stop scan automatically turns on the LCD backlight when the scan stops.

Compact body

56(W)×97(H)×36.4(D) mm* compact body with durable, dependable construction, has been tested to MIL standard specifications.
* 2⁷⁄₃₂(W)×3¹³⁄₁₆(H)×1⁷⁄₁₆(D) in

Li-Ion battery pack

The large capacity 1700mAh Lithium-Ion (Li-Ion) battery pack, BP-227 provides a practical 9–10 hours* of operating time.
* Typical operation Tx:Rx: Stand-by=5:5:90

Other features

• 128 memory channels with 8 zones
• Inversion type^*1 voice scrambler built-in
• Optional VOX headsets available
• Optional GPS speaker-microphone
• Power ON password
• Radio stun/kill/revive
• 8 DTMF autodial
• Normal and priority scans
• 2-step power saver and 2-step low battery beep
• BIIS 1200 mode programmable
• Busy, repeater lockout functions
• BTL only version (no vibration alert and no voice recorder).

Specifications

General
Frequency range	IC-F50V 136-174 MHz IC-F60V 400-470 MHz 450-512 MHz (U.S.A.) 450-520 MHz (General)
Number of Channels	Max. 128 channels/ 8 zones
Channel spacing	12.5/25 kHz, 15/30 kHz
Antenna impedance	50 Ω (SMA Type)
Frequency error	±2.5ppm
PLL channel step	2.5/3.125 kHz
Power supply requirements	7.2V DC
Current drain (approx.) Transmit Receive	5W 1W AF max. Stand-by 1.8A 0.7A 500mA (Internal speaker) 350mA (External Speaker) 85mA
Operating temperature range	–30°C to +60°C –22°F to +140°F
Dimensions (W x H x D) (projections not included)	56 × 97 × 36.4mm 27⁄32 × 313⁄16 × 17⁄16 in.
Weight (approx.)	VHF: 280g; 9.9oz (With BP-227) UHF: 284g; 10.0oz (With BP-227)

Transmitter
Output power IC-F50V IC-F60V	5.0W 4.0W
Modulation system	Variable reactance frequency modulation
Max. frequency deviation	±5 kHz (wide) ±2.5 kHz (narrow)
Modulation limiting	60-100% of Max. deviation
Audio harmonic distortion	3% typ. (AF 1 kHz, 40% deviation)
Spurious emissions	70dB typ.
Adjacent channel power	70dB Min. (wide) 60dB Min. (narrow)
FM Hum and Noise	46dB typ. (wide) 40dB typ. (narrow)
External microphone impedance	9-pin multi connector/2.2kΩ

Receiver
Sensitivity	0.25µV typ. (at 12db SINAD)
Squelch sensitivity	0.25µV typ. (at threshold)
Adjacent channel selectivity	75dB typ. (wide) 65dB typ. (narrow)
Spurious response	70dB
Intermodulation	74dB typ.
Hum and noise	45db typ. (wide) 40dB typ. (narrow)
Audio output power	0.7W typ. (Internal speaker) 0.5W typ. (external speaker) at 5% distortion with an 8Ω load
External SP connector	9-pin multi connector/8Ω

Applicable U.S. Military Specifications

Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and Ingress Protection standards.

Standard	MIL 810 C		MIL 810 D		MIL 810 E		MIL 810 F
	Method	Proc	Method	Proc	Method	Proc	Method	Proc
Low Pressure	500.1	I	500.2	I, II	500.3	I, II	500.4	I, II
High Temp.	501.1	I	501.2	I, II	501.3	I, II	501.4	I, II
Low Temp.	502.1	I	502.2	I, II	502.3	I, II	502.4	I, II
Temp. Shock	503.1	I	503.2	I	503.3	I	503.4	I
Solar Radiation	505.1	I	505.2	I	505.3	I	505.4	I
Rain	506.1	I, II	506.2	I, II	506.3	I, II	506.4	I, II
Humidity	507.1	I, II	507.2	II, III	507.3	II, III	507.4	–
Salt Fog	509.1	I	509.2	I	509.3	I	509.4	–
Dust	510.1	I	510.2	I	510.3	I	510.4	I
Vibration	514.2	VIII, X	514.3	I	514.4	I	514.5	I
Shock	516.2	I, II, V	516.3	I, IV	516.4	I, IV	516.5	I, IV

Ingress Protection Standard
Dust & Water	IP67 (Dust-tight and waterproof protection)

Measurements made in accordance with EIA-152C/204D, TIA-603. All stated specifications are subject to change without notice or obligation.